How to Replace a Kia Sportage Replacement Key
For a number of Kia models keys, there is a keyless entry system built-in. This key usually resembles a remote control and can be exchanged by a new one purchased from a Kia dealer or a locksmith.
Key fobs might stop working due to a variety of reasons, including a dead coin battery worn buttons signals, signal interference, water damage and a damaged receiver module. Here are some suggestions to assist you in getting your Kia sportage replacement key to work once more.
How do you replace a remote key or a smartkey?
The battery inside your Kia's smart key will eventually have to be replaced, whether it's a remote, a push-to-start key or a standard metal key that is not equipped with an electronic transponder. This is especially in the event that your car displays a message telling that the remote or smart key has a low battery.
This is a relatively easy procedure. To replace the key fob battery take out the mechanical key from the hole in the back of the key fob. You then need to remove the cover. A small screw will be in the key fob that holds the battery in the correct position. Remove the old battery by unwinding the screw using the help of a small screwdriver. Then, you can insert the new battery and close the slit inside the key fob.
Test the key fob by pressing the lock or unlock buttons. You're good to go when the doors lock or unlock as you expect. You can now utilize the hands-free feature to lock and unlock your Kia whenever your fingers feel cold or when you need to go on errands around Brandon.
Note: Some key fobs (transponder chip or smart keys) may require their programming done. This requires a programing machine that is only available to the locksmith in the automotive or dealer. Other keys (non-transponder metal keys) do not require programming. If your key requires to be programmed, you will need to be aware of the key code number printed on the key code tag and then record the number in a secure place.
How to replace a battery
If the Kia key fob does not respond to pressing the lock/unlock button, it's a sign that the battery is low. A battery that is not functioning properly could cause other issues, such as the check engine light coming on or delayed cranking of the engine. It is fairly easy to replace the key fob batteries by using only the use of a few tools.
Before you begin, make sure that your vehicle is off and all doors are shut. Find the small, metal or plastic piece on the bottom of the key fob. Move it until the metal key pops out. This key can be put into the driver door handle to unlock your car.
To replace the battery on the key fob, take off the rear cover. Use a pry tool to loosen up the latch that holds the black negative cable. Remove the old battery and then align the replacement battery to ensure its "+" side is facing you and the "-" negative side is facing the fob's electrical contacts. Avoid using too much force when pushing the new CR2032 into place to avoid damaging or breaking the metal contacts.
Once the new battery has been installed then turn the key fob off and back on in the ignition repeatedly until the door locks cycle. Then you can test your Kia key fob to determine if it is working properly again.
How to replace the smart key?
You may have either the standard keyfob or Smart Key depending on the model of Kia Sportage. The smart key comes with an embedded mechanical key blade, unlike the standard key fob, which does not. Both key fobs come with an internal battery that will eventually need to be changed. This is a simple procedure that takes less than two minutes.
Before kia optima keys begin before you begin, ensure that you're on a level surface with enough lighting and that your Kia is not on. Keep in mind that the fob is made up of tiny parts that could be thrown off if you're not careful.
The release button for the small size is located on the lower backside. It will be a circular button or rectangular slot. When you press it, the mechanical key blade will appear and you will be able to open the key fob.
After the key fob has been open, remove the battery that was in it. The new battery should be a CR-2032 and can be purchased online or at a local auto parts store. When you're done, the key fob should be able to lock, unlock, and start your vehicle even if it's not running.
How to replace a mechanical key
The Kia key fob is a great convenience that lets us lock and unlock our vehicle with the press of the button. However, like all devices there are issues with it occasionally. There are solutions to resolve these issues and keep your key fobs functioning for a long time.
One of the most common issues is a low or dead battery. The battery could cause the device to stop working or work intermittently. If this is the problem, replace the battery with an entirely new battery.
If this doesn't solve the problem, use a flathead screwdriver standard to wedge the plastic casing of the fob open. Be sure not to damage any internal components or scratch the plastic. After opening, carefully remove the old battery and replace it with a new one.
After the new battery has been put in, shut and open the doors using the mechanical key (every Kia fob comes with an emergency mechanical key that will fit in the slot). Test the key fob to ensure it's functioning properly. Contact a dealer or locksmith to resolve the problem in the event that the key fob is not working. Make sure they cut you an emergency key that can work for all trunk and door cylinders, to avoid lockouts again.